Articoli correlati a Spindles: 27
Sinossi
If you do not own a milling machine (and even if you do) what you can achieve in your workshop is greatly enhanced if you own a spindle or two for use with your lathe. Spindles come in many shapes and sizes, ranging from 19mm (0.75 in) to 57 mm (2.25 in) in diameter, depending on the uses envisaged for them. This book describes the design, construction and use of a variety of spindles that will be of interest to the amateur engineer. Milling, grinding and drilling spindles are covered along with a unique light gear-cutting frame for clockmakers. The emphasis is on spindles that are easy to make and have as few parts as possible; all but one for example use sealed ball bearings (the exception uses tapered collar bearings and thus needs to have seals installed to protect the bearings.) The basic spindle described uses the same spindle nose as the Myford Super 7 lathe; this allows all chucks, plates, collets and closers designed for the lathe to be used with this spindle. It can also be modified for other lathe nose standards.
Le informazioni nella sezione "Riassunto" possono far riferimento a edizioni diverse di questo titolo.
Informazioni sull'autore
Harprit Singh Sandhu, BSME, MSCerE, is an American engineer and the founder of Rhino Robots Inc., where he was the chief designer of the ''Rhino'' series of robots. In his spare time he is a journeyman designer, machinist & woodworker, whose interest in clock making led him to design & build the spindles described in the book.
Le informazioni nella sezione "Su questo libro" possono far riferimento a edizioni diverse di questo titolo.
Risultati della ricerca per Spindles: 27
Foto dell'editore
Spindles
Editore:
Fox Chapel Publishers International, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Antico o usato
Paperback
Da: World of Books (was SecondSale), Montgomery, IL, U.S.A.
Valutazione del venditore 5 su 5 stelle
Paperback. Condizione: Good. If you do not own a milling machine (and even if you do) what you can achieve in your workshop is greatly enhanced if you own a spindle or two for use with your lathe. Spindles come in many shapes and sizes, ranging from 19mm (0.75 in) to 57 mm (2.25 in) in diameter, depending on the uses envisaged for them. This book describes the design, construction and use of a variety of spindles that will be of interest to the amateur engineer. Milling, grinding and drilling spindles are covered along with a unique light gear-cutting frame for clockmakers. The emphasis is on spindles that are easy to make and have as few parts as possible; all but one for example use sealed ball bearings (the exception uses tapered collar bearings and thus needs to have seals installed to protect the bearings.) The basic spindle described uses the same spindle nose as the Myford Super 7 lathe; this allows all chucks, plates, collets and closers designed for the lathe to be used with this spindle. It can also be modified for other lathe nose standards. Codice articolo CIN1854861492G
Compra usato
EUR 8,78
Spedizione gratuita
Spedito in U.S.A.
Spedito in U.S.A.
Quantità: 1 disponibili
Foto dell'editore
Spindles
Editore:
Fox Chapel Publishers International, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Antico o usato
Paperback
Da: World of Books Inc, Montgomery, IL, U.S.A.
Valutazione del venditore 4 su 5 stelle
Paperback. Condizione: Good. If you do not own a milling machine (and even if you do) what you can achieve in your workshop is greatly enhanced if you own a spindle or two for use with your lathe. Spindles come in many shapes and sizes, ranging from 19mm (0.75 in) to 57 mm (2.25 in) in diameter, depending on the uses envisaged for them. This book describes the design, construction and use of a variety of spindles that will be of interest to the amateur engineer. Milling, grinding and drilling spindles are covered along with a unique light gear-cutting frame for clockmakers. The emphasis is on spindles that are easy to make and have as few parts as possible; all but one for example use sealed ball bearings (the exception uses tapered collar bearings and thus needs to have seals installed to protect the bearings.) The basic spindle described uses the same spindle nose as the Myford Super 7 lathe; this allows all chucks, plates, collets and closers designed for the lathe to be used with this spindle. It can also be modified for other lathe nose standards. Codice articolo CIN1854861492G
Compra usato
EUR 10,62
Spedizione gratuita
Spedito in U.S.A.
Spedito in U.S.A.
Quantità: 1 disponibili
Foto dell'editore
Spindles: 27 (Workshop Practice Series)
Editore:
Special Interest Model Books, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Antico o usato
Paperback
Da: WorldofBooks, Goring-By-Sea, WS, Regno Unito
Valutazione del venditore 5 su 5 stelle
Paperback. Condizione: Very Good. The book has been read, but is in excellent condition. Pages are intact and not marred by notes or highlighting. The spine remains undamaged. Codice articolo GOR002732465
Compra usato
EUR 4,40
Spedizione EUR 6,71
Spedito da Regno Unito a U.S.A.
Spedito da Regno Unito a U.S.A.
Quantità: 3 disponibili
Foto dell'editore
Spindles (Workshop Practice Series)
Editore:
Special Interest Model Books, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Antico o usato
Paperback
Da: ThriftBooks-Dallas, Dallas, TX, U.S.A.
Valutazione del venditore 5 su 5 stelle
Paperback. Condizione: Very Good. No Jacket. May have limited writing in cover pages. Pages are unmarked. ~ ThriftBooks: Read More, Spend Less. Codice articolo G1854861492I4N00
Compra usato
EUR 12,43
Spedizione gratuita
Spedito in U.S.A.
Spedito in U.S.A.
Quantità: 1 disponibili
Foto dell'editore
Spindles (Workshop Practice Series)
Editore:
Special Interest Model Books, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Antico o usato
Paperback
Da: ThriftBooks-Atlanta, AUSTELL, GA, U.S.A.
Valutazione del venditore 5 su 5 stelle
Paperback. Condizione: Very Good. No Jacket. May have limited writing in cover pages. Pages are unmarked. ~ ThriftBooks: Read More, Spend Less. Codice articolo G1854861492I4N00
Compra usato
EUR 12,43
Spedizione gratuita
Spedito in U.S.A.
Spedito in U.S.A.
Quantità: 1 disponibili
Foto dell'editore
Spindles : Comprehensive Guide to Making Light Milling or Grinding Spindles with a Small Lathe
Editore:
Special Interest Model Books, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Antico o usato
Brossura
Da: Better World Books Ltd, Dunfermline, Regno Unito
Valutazione del venditore 5 su 5 stelle
Condizione: Good. Pages intact with minimal writing/highlighting. The binding may be loose and creased. Dust jackets/supplements are not included. Stock photo provided. Product includes identifying sticker. Better World Books: Buy Books. Do Good. Codice articolo 18728907-6
Compra usato
EUR 7,87
Spedizione EUR 5,99
Spedito da Regno Unito a U.S.A.
Spedito da Regno Unito a U.S.A.
Quantità: 1 disponibili
Immagini fornite dal venditore
Spindles
Editore:
Special Interest Model Books, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Nuovo
Brossura
Da: GreatBookPrices, Columbia, MD, U.S.A.
Valutazione del venditore 5 su 5 stelle
Condizione: New. Codice articolo 1484716-n
Compra nuovo
EUR 13,11
Spedizione EUR 2,35
Spedito in U.S.A.
Spedito in U.S.A.
Quantità: 1 disponibili
Immagini fornite dal venditore
Spindles
Editore:
Special Interest Model Books, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Antico o usato
Brossura
Da: GreatBookPrices, Columbia, MD, U.S.A.
Valutazione del venditore 5 su 5 stelle
Condizione: As New. Unread book in perfect condition. Codice articolo 1484716
Compra usato
EUR 13,14
Spedizione EUR 2,35
Spedito in U.S.A.
Spedito in U.S.A.
Quantità: 1 disponibili
Immagini fornite dal venditore
Spindles
Editore:
Fox Chapel Publishers International, GB, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Nuovo
Paperback
Da: Rarewaves.com USA, London, LONDO, Regno Unito
Valutazione del venditore 5 su 5 stelle
Paperback. Condizione: New. If you do not own a milling machine (and even if you do) what you can achieve in your workshop is greatly enhanced if you own a spindle or two for use with your lathe. Spindles come in many shapes and sizes, ranging from 19mm (0.75 in) to 57 mm (2.25 in) in diameter, depending on the uses envisaged for them. This book describes the design, construction and use of a variety of spindles that will be of interest to the amateur engineer. Milling, grinding and drilling spindles are covered along with a unique light gear-cutting frame for clockmakers. The emphasis is on spindles that are easy to make and have as few parts as possible; all but one for example use sealed ball bearings (the exception uses tapered collar bearings and thus needs to have seals installed to protect the bearings.) The basic spindle described uses the same spindle nose as the Myford Super 7 lathe; this allows all chucks, plates, collets and closers designed for the lathe to be used with this spindle. It can also be modified for other lathe nose standards. Codice articolo LU-9781854861498
Compra nuovo
EUR 15,54
Spedizione gratuita
Spedito da Regno Unito a U.S.A.
Spedito da Regno Unito a U.S.A.
Quantità: 5 disponibili
Foto dell'editore
Spindles
Editore:
Fox Chapel Publishers International, 1998
ISBN 10: 1854861492
ISBN 13: 9781854861498
Nuovo
PAP
Da: PBShop.store US, Wood Dale, IL, U.S.A.
Valutazione del venditore 5 su 5 stelle
PAP. Condizione: New. New Book. Shipped from UK. Established seller since 2000. Codice articolo GB-9781854861498
Compra nuovo
EUR 15,81
Spedizione gratuita
Spedito in U.S.A.
Spedito in U.S.A.
Quantità: 2 disponibili