Gavali pankaj (42 risultati)

Condizione: New.

Condizione: New.

Condizione: New.

Paperback. Condizione: Neu. Neu Neuware, auf Lager - Technical Report from the year 2022 in the subject Engineering - Mechanical Engineering, , course: Mechanical, language: English, abstract: Biomass derived vegetable oils are quite promising alternative fuels for agricultural diesel engines. Use of vegetable oils in diesel engines leads to slightly inferior performance and higher smoke emissions due to their high viscosity. The performance of vegetable oils can be improved by modifying them through the transesterification process. In the present work, the performance of single cylinder water-cooled diesel engine using methyl-ester of Jatropha and Karanja oil as fuel was evaluated for its performance and exhaust emissions. The fuel properties of biodiesel such as kinematic viscosity, calorific value, flash point, carbon residue and specific gravity were found. Results indicated that B25 has closer performance to diesel and B100 has lower brake thermal efficiency, mainly due to its high viscosity compared to diesel. The brake thermal efficiency for biodiesel and its blends was found to be slightly higher than that of diesel fuel at tested load conditions and there was no difference between the biodiesel and its blended fuels efficiencies. For Jatropha and karanja biodiesel and its blended fuels, the exhaust gas temperature increased with increase in power and amount of biodiesel. But, diesel blends showed reasonable efficiency, lower smoke, CO2, CO and HC.…

Taschenbuch. Condizione: Neu. Optimization of Cutting Parameters In Turning Process | Pankaj Gavali | Taschenbuch | 60 S. | Englisch | 2019 | LAP LAMBERT Academic Publishing | EAN 9786139453702 | Verantwortliche Person für die EU: preigu GmbH & Co. KG, Lengericher Landstr. 19, 49078 Osnabrück, mail[at]preigu[dot]de | Anbieter: preigu. …

Taschenbuch. Condizione: Neu. Optimization of changing polarity | in Powder Mixed Electric Discharge Machining (PM-EDM) | Pankaj Gavali (u. a.) | Taschenbuch | Englisch | 2023 | Scholars' Press | EAN 9786205523834 | Verantwortliche Person für die EU: preigu GmbH & Co. KG, Lengericher Landstr. 19, 49078 Osnabrück, mail[at]preigu[dot]de | Anbieter: preigu. …

paperback. Condizione: New. NEW. SHIPS FROM MULTIPLE LOCATIONS. book.

Taschenbuch. Condizione: Neu. Optimisation du changement de polarité | dans l'usinage par décharge électrique de poudres mélangées (PM-EDM) | Pankaj Gavali (u. a.) | Taschenbuch | Französisch | 2024 | Editions Notre Savoir | EAN 9786207157464 | Verantwortliche Person für die EU: SIA OmniScriptum Publishing, Brivibas Gatve 197, 1039 RIGA, LETTLAND, customerservice[at]vdm-vsg[dot]de | Anbieter: preigu.…

Taschenbuch. Condizione: Neu. Ottimizzazione del cambio di polarità | nella lavorazione a scarica elettrica mista a polvere (PM-EDM) | Pankaj Gavali (u. a.) | Taschenbuch | Italienisch | 2024 | Edizioni Sapienza | EAN 9786207157471 | Verantwortliche Person für die EU: SIA OmniScriptum Publishing, Brivibas Gatve 197, 1039 RIGA, LETTLAND, customerservice[at]vdm-vsg[dot]de | Anbieter: preigu. …

Taschenbuch. Condizione: Neu. Otimização da mudança de polaridade | na maquinagem por descarga eléctrica com mistura de pós (PM-EDM) | Pankaj Gavali (u. a.) | Taschenbuch | Portugiesisch | 2024 | Edições Nosso Conhecimento | EAN 9786207157488 | Verantwortliche Person für die EU: SIA OmniScriptum Publishing, Brivibas Gatve 197, 1039 RIGA, LETTLAND, customerservice[at]vdm-vsg[dot]de | Anbieter: preigu.…

Taschenbuch. Condizione: Neu. Optimierung des Polaritätswechsels | bei der pulvergemischten Funkenerosion (PM-EDM) | Pankaj Gavali (u. a.) | Taschenbuch | 60 S. | Deutsch | 2024 | Verlag Unser Wissen | EAN 9786207157440 | Verantwortliche Person für die EU: SIA OmniScriptum Publishing, Brivibas Gatve 197, 1039 RIGA, LETTLAND, customerservice[at]vdm-vsg[dot]de | Anbieter: preigu.…

Taschenbuch. Condizione: Neu. This item is printed on demand - it takes 3-4 days longer - Neuware -Technical Report from the year 2022 in the subject Engineering - Mechanical Engineering, , course: Mechanical, language: English, abstract: Biomass derived vegetable oils are quite promising alternative fuels for agricultural diesel engines. Use of vegetable oils in diesel engines leads to slightly inferior performance and higher smoke emissions due to their high viscosity. The performance of vegetable oils can be improved by modifying them through the transesterification process. In the present work, the performance of single cylinder water-cooled diesel engine using methyl-ester of Jatropha and Karanja oil as fuel was evaluated for its performance and exhaust emissions. The fuel properties of biodiesel such as kinematic viscosity, calorific value, flash point, carbon residue and specific gravity were found. Results indicated that B25 has closer performance to diesel and B100 has lower brake thermal efficiency, mainly due to its high viscosity compared to diesel. The brake thermal efficiency for biodiesel and its blends was found to be slightly higher than that of diesel fuel at tested load conditions and there was no difference between the biodiesel and its blended fuels efficiencies. For Jatropha and karanja biodiesel and its blended fuels, the exhaust gas temperature increased with increase in power and amount of biodiesel. But, diesel blends showed reasonable efficiency, lower smoke, CO2, CO and HC. 60 pp. Englisch.…

Taschenbuch. Condizione: Neu. This item is printed on demand - it takes 3-4 days longer - Neuware -High productivity is the basic need of any manufacturing industry nowadays because of high quality product demand and cost efficiency. Turning is the basic operation in manufacturing and to optimize the process, the output parameters like material removal rate that is to be maximized and surface finish which is to be minimized, must be assessed at close look. The book gives the effect of input parameters (cutting speed, depth of cut and feed rate) on the parameters of the turning process. Three levels of each parameter are selected within the operating range and the experimental runs are performed according to Taguchi's L-27 orthogonal array. The turning on EN9 specimen is carried out on CNC lathe. The material removal rate is found out by weight difference method and surface roughness is tested by Surftest 201 Mitutoyo surface roughness meter. 60 pp. Englisch.…

Condizione: New. Print on Demand.

Condizione: New. Print on Demand.

Taschenbuch. Condizione: Neu. nach der Bestellung gedruckt Neuware - Printed after ordering - High productivity is the basic need of any manufacturing industry nowadays because of high quality product demand and cost efficiency. Turning is the basic operation in manufacturing and to optimize the process, the output parameters like material removal rate that is to be maximized and surface finish which is to be minimized, must be assessed at close look. The book gives the effect of input parameters (cutting speed, depth of cut and feed rate) on the parameters of the turning process. Three levels of each parameter are selected within the operating range and the experimental runs are performed according to Taguchi's L-27 orthogonal array. The turning on EN9 specimen is carried out on CNC lathe. The material removal rate is found out by weight difference method and surface roughness is tested by Surftest 201 Mitutoyo surface roughness meter.…

Taschenbuch. Condizione: Neu. This item is printed on demand - it takes 3-4 days longer - Neuware -Electrical Discharge Machining (EDM) is a well-established non-conventional machining process for the machining of electrically conductive and difficult-to-machine materials. But its applications are limited because of the slow machining rate and poor surface finish. Powder mixed EDM (PMEDM) is unitary of the recent progresses in the EDM process in which powder particles mixed in the dielectric fluid results in higher machining rate and better surface quality.In straight polarity or normal polarity of EDM, workpiece is positive and tool is negative. When workpiece is negative and tool is positive, this type of polarity is commonly known as reversed polarity. As discussed earlier, energy dissipation into the anode is greater than cathode during sparking. 76 pp. Englisch.…

Condizione: New. PRINT ON DEMAND.

Condizione: New. PRINT ON DEMAND.

Condizione: New. Dieser Artikel ist ein Print on Demand Artikel und wird nach Ihrer Bestellung fuer Sie gedruckt. Autor/Autorin: Gavali PankajPankaj B. Gavali Working as an Assistant Professor at Sanjay Ghodawat Institute, Kolhapur, India. I am expertise in the Manufacturing Engineering, Production Engineering.High productivity is the basic need of any man.…

Taschenbuch. Condizione: Neu. nach der Bestellung gedruckt Neuware - Printed after ordering - Electrical Discharge Machining (EDM) is a well-established non-conventional machining process for the machining of electrically conductive and difficult-to-machine materials. But its applications are limited because of the slow machining rate and poor surface finish. Powder mixed EDM (PMEDM) is unitary of the recent progresses in the EDM process in which powder particles mixed in the dielectric fluid results in higher machining rate and better surface quality.In straight polarity or normal polarity of EDM, workpiece is positive and tool is negative. When workpiece is negative and tool is positive, this type of polarity is commonly known as reversed polarity. As discussed earlier, energy dissipation into the anode is greater than cathode during sparking.…

Taschenbuch. Condizione: Neu. This item is printed on demand - Print on Demand Titel. Neuware -Technical Report from the year 2022 in the subject Engineering - Mechanical Engineering, , course: Mechanical, language: English, abstract: Biomass derived vegetable oils are quite promising alternative fuels for agricultural diesel engines. Use of vegetable oils in diesel engines leads to slightly inferior performance and higher smoke emissions due to their high viscosity. The performance of vegetable oils can be improved by modifying them through the transesterification process. In the present work, the performance of single cylinder water-cooled diesel engine using methyl-ester of Jatropha and Karanja oil as fuel was evaluated for its performance and exhaust emissions. The fuel properties of biodiesel such as kinematic viscosity, calorific value, flash point, carbon residue and specific gravity were found. Results indicated that B25 has closer performance to diesel and B100 has lower brake thermal efficiency, mainly due to its high viscosity compared to diesel. The brake thermal efficiency for biodiesel and its blends was found to be slightly higher than that of diesel fuel at tested load conditions and there was no difference between the biodiesel and its blended fuels efficiencies. For Jatropha and karanja biodiesel and its blended fuels, the exhaust gas temperature increased with increase in power and amount of biodiesel. But, diesel blends showed reasonable efficiency, lower smoke, CO2, CO and HC.Books on Demand GmbH, Überseering 33, 22297 Hamburg 60 pp. Englisch.…

Taschenbuch. Condizione: Neu. This item is printed on demand - it takes 3-4 days longer - Neuware 60 pp. Spanisch.

Condizione: New. Dieser Artikel ist ein Print on Demand Artikel und wird nach Ihrer Bestellung fuer Sie gedruckt. Electrical Discharge Machining (EDM) is a well-established non-conventional machining process for the machining of electrically conductive and difficult-to-machine materials. But its applications are limited because of the slow machining rate and poor surfa.…

Taschenbuch. Condizione: Neu. Performance of Diesel Engine Using Jatropha and Karanja Oil and its Blends | Pankaj Gavali | Taschenbuch | Englisch | 2022 | GRIN Verlag | EAN 9783346616968 | Verantwortliche Person für die EU: preigu GmbH & Co. KG, Lengericher Landstr. 19, 49078 Osnabrück, mail[at]preigu[dot]de | Anbieter: preigu Print on Demand. …

Taschenbuch. Condizione: Neu. This item is printed on demand - Print on Demand Titel. Neuware -High productivity is the basic need of any manufacturing industry nowadays because of high quality product demand and cost efficiency. Turning is the basic operation in manufacturing and to optimize the process, the output parameters like material removal rate that is to be maximized and surface finish which is to be minimized, must be assessed at close look. The book gives the effect of input parameters (cutting speed, depth of cut and feed rate) on the parameters of the turning process. Three levels of each parameter are selected within the operating range and the experimental runs are performed according to Taguchi's L-27 orthogonal array. The turning on EN9 specimen is carried out on CNC lathe. The material removal rate is found out by weight difference method and surface roughness is tested by Surftest 201 Mitutoyo surface roughness meter.VDM Verlag, Dudweiler Landstraße 99, 66123 Saarbrücken 60 pp. Englisch.…

Taschenbuch. Condizione: Neu. nach der Bestellung gedruckt Neuware - Printed after ordering - El mecanizado por descarga eléctrica (EDM) es un proceso de mecanizado no convencional bien establecido para el mecanizado de materiales conductores de la electricidad y difíciles de mecanizar. Pero sus aplicaciones son limitadas debido a la lentitud del mecanizado y al escaso acabado superficial. La electroerosión por mezcla de polvo (PMEDM) es uno de los avances más recientes en el proceso de electroerosión, en el que las partículas de polvo mezcladas en el fluido dieléctrico dan como resultado una mayor velocidad de mecanizado y una mejor calidad superficial. Cuando la pieza es negativa y la herramienta positiva, este tipo de polaridad se conoce comúnmente como polaridad invertida. Como se ha comentado anteriormente, la disipación de energía en el ánodo es mayor que en el cátodo durante el chispeo.…

Taschenbuch. Condizione: Neu. This item is printed on demand - Print on Demand Titel. Neuware -Electrical Discharge Machining (EDM) is a well-established non-conventional machining process for the machining of electrically conductive and difficult-to-machine materials. But its applications are limited because of the slow machining rate and poor surface finish. Powder mixed EDM (PMEDM) is unitary of the recent progresses in the EDM process in which powder particles mixed in the dielectric fluid results in higher machining rate and better surface quality.In straight polarity or normal polarity of EDM, workpiece is positive and tool is negative. When workpiece is negative and tool is positive, this type of polarity is commonly known as reversed polarity. As discussed earlier, energy dissipation into the anode is greater than cathode during sparking.VDM Verlag, Dudweiler Landstraße 99, 66123 Saarbrücken 76 pp. Englisch.…

Taschenbuch. Condizione: Neu. This item is printed on demand - it takes 3-4 days longer - Neuware 60 pp. Französisch.

Taschenbuch. Condizione: Neu. nach der Bestellung gedruckt Neuware - Printed after ordering - L'usinage par décharge électrique (EDM) est un procédé d'usinage non conventionnel bien établi pour l'usinage de matériaux conducteurs d'électricité et difficiles à usiner. Mais ses applications sont limitées en raison de la lenteur de l'usinage et de la médiocrité de la finition de surface. L'électroérosion par mélange de poudres (PMEDM) est l'un des progrès récents du processus d'électroérosion dans lequel des particules de poudre mélangées au fluide diélectrique permettent d'obtenir une vitesse d'usinage plus élevée et une meilleure qualité de surface.En polarité droite ou normale de l'électroérosion, la pièce est positive et l'outil est négatif. Lorsque la pièce est négative et l'outil positif, ce type de polarité est communément appelé polarité inversée. Comme nous l'avons vu précédemment, la dissipation d'énergie dans l'anode est plus importante que dans la cathode lors de la production d'étincelles.…