Chatha sukhpal singh (17 risultati)

Condizione: New. pp. 60.

Condizione: New.

Condizione: New. pp. 64.

Taschenbuch. Condizione: Neu. Electrical Discharge Machining using Powder-Mixed Dielectric | Sukhpal Singh Chatha (u. a.) | Taschenbuch | 60 S. | Englisch | 2014 | LAP LAMBERT Academic Publishing | EAN 9783659525131 | Verantwortliche Person für die EU: preigu GmbH & Co. KG, Lengericher Landstr. 19, 49078 Osnabrück, mail[at]preigu[dot]de | Anbieter: preigu. …

paperback. Condizione: New. NEW. SHIPS FROM MULTIPLE LOCATIONS. book.

Taschenbuch. Condizione: Neu. This item is printed on demand - it takes 3-4 days longer - Neuware -Electrical discharge machining (EDM) is one of the most widely disseminated manufacturing technologies, in particular as regards the generation of accurate and complex geometrical shapes on hard metallic components. Nevertheless, current EDM has major limitations when dealing with fine surface finish and material removal rate. Recently EDM with powder mixed dielectric (PMEDM) has been a focus of intense research work in order to overcome these technological performance barriers. The present study is done with an objective to modify the machining characteristics like surface roughness, material removal rate, and hardness by adding different concentrations of TiO2 into the dielectric fluid of EDM. XRD and MAPING analysis has been carried out to find the migration of powder from the dielectric to the machined surface. SEM of the surface and the cross-section is also done to analyze the surface texture and recast layer. The results achieved show that minor amount of powder was migrated to machined surface, which resulted in surface improvement. The dielectric with added powder also shows significant improvement in material removal rate. 60 pp. Englisch.…

Condizione: New. Print on Demand pp. 60 2:B&W 6 x 9 in or 229 x 152 mm Perfect Bound on Creme w/Gloss Lam.

Condizione: New. Print on Demand pp. 64 2:B&W 6 x 9 in or 229 x 152 mm Perfect Bound on Creme w/Gloss Lam.

Condizione: New. Print on Demand.

Condizione: New. PRINT ON DEMAND pp. 60.

Taschenbuch. Condizione: Neu. nach der Bestellung gedruckt Neuware - Printed after ordering - In all machining processes, tool wear is a natural phenomenon and it leads to tool failure. In metal industries, the use of cutting fluids has become more problematic in terms of both employee health and environmental pollution. But the use of cutting fluids becomes necessary to keep tight tolerances and to maintain the work-piece's surface properties without damages. Industries and researchers are trying to reduce the use of coolant lubricant fluids in metal cutting to obtain safety, environmental and economical benefits. So to minimize the use of cutting fluids new cutting techniques are investigated. Minimal quantity of Lubrication (MQL) is a recent technique introduced in machining to obtain less tool wear and environment safety. The minimum quantity lubrication was provided with a spray of air and vegetable oil. MQL machining was performed much superior compared to dry and wet machining due to substantial reduction in tool wear and cutting zone temperature and a better surface finish. MQL provides neat and clean environment avoiding health hazards due to smoke, fumes and gases etc.…

Condizione: New. PRINT ON DEMAND.

Condizione: New. PRINT ON DEMAND pp. 64.

Condizione: New. Dieser Artikel ist ein Print on Demand Artikel und wird nach Ihrer Bestellung fuer Sie gedruckt. Autor/Autorin: Pal AmritEr. Amrit Pal Assistant ProfessorGZS-PTU campus, Bathinda (India)Dr. Sukhpal Singh ChathaAssistant Professor,Yadavindra College of Engineering,Talwandi Sabo, Punjab (India)Use of cutting fluids in metal cutting enhances . …

Condizione: New. Dieser Artikel ist ein Print on Demand Artikel und wird nach Ihrer Bestellung fuer Sie gedruckt. Autor/Autorin: Chatha Sukhpal SinghSukhpal Singh Chatha and Hazoor Singh, working as faculty of Mechanical Engineering with Punjabi University Guru Kashi Campus, Talwandi Sabo, Punjab, India.Electrical discharge machining (EDM) is one of the mo. …

Condizione: New. Dieser Artikel ist ein Print on Demand Artikel und wird nach Ihrer Bestellung fuer Sie gedruckt. Autor/Autorin: Mittal RutashDr. Rutash Mittal Assistant Professor in Mechanical Engineering Department and In-charge of University Regional Centre (M.Tech.Studies) inMalout Institute of Management & Information Technology (MIMIT)(Estab. by Govt. of.…

Taschenbuch. Condizione: Neu. This item is printed on demand - Print on Demand Titel. Neuware -Electrical discharge machining (EDM) is one of the most widely disseminated manufacturing technologies, in particular as regards the generation of accurate and complex geometrical shapes on hard metallic components. Nevertheless, current EDM has major limitations when dealing with fine surface finish and material removal rate. Recently EDM with powder mixed dielectric (PMEDM) has been a focus of intense research work in order to overcome these technological performance barriers. The present study is done with an objective to modify the machining characteristics like surface roughness, material removal rate, and hardness by adding different concentrations of TiO2 into the dielectric fluid of EDM. XRD and MAPING analysis has been carried out to find the migration of powder from the dielectric to the machined surface. SEM of the surface and the cross-section is also done to analyze the surface texture and recast layer. The results achieved show that minor amount of powder was migrated to machined surface, which resulted in surface improvement. The dielectric with added powder also shows significant improvement in material removal rate.VDM Verlag, Dudweiler Landstraße 99, 66123 Saarbrücken 60 pp. Englisch.…